top of page
Stainless Steel Checker Plate
Stainless steel checker plates serve as an optimal selection for both indoor and outdoor building decor materials, providing a distinctive convex diamond pattern that ensures not only aesthetic appeal but also enhanced safety and grip for individuals traversing its surface.
TOUGH MATERIAL
The stainless steel Checker plate features a surface that is hot rolled, annealed, and pickled, offering a blend of high strength and exceptional corrosion resistance. This combination renders it an excellent material for applications such as walkways, ditch coverings, sidewalks, and decorative projects.
Standard | ASTM | AISI | EN | JIS |
|---|---|---|---|---|
S30400 | 304 | 1.4301 | SUS304 | |
GRADES | S30403 | 304L | 1.4307 | - |
S31603 | 316L | 1.4404 | - |
Available Stainelss Steel Checker Plate Dimensions
Grade | Thickness(mm) | Width(mm) | Surface Finish | I.D(mm) |
|---|---|---|---|---|
304(L), 316L | 3.00mm - 6.00mm. | Custom-made
specification is
available | Checker Patterns | - |
Diagram of Stainless
Steel Checker Plate
Application of Stainless
Steel Checker Plate
Stainless Steel Plate floors are widely used on trucks.
Chemical Composition of ASTM-A480 Stainless Steel
Grade | Carbon(C)% | Nickel(Ni) % | Chromium(Cr)% |
|---|---|---|---|
S30400 / 304 | 0.07 | 8.0-10.5 | 16-18 |
S30403 / 304L | 0.03 | 8.0-12 | 16-18 |
S301603 / 316L | 0.03 | 10-14 | 16-18 |
Mechanical Property of ASTM-A480 Stainless Steel
Grade | Yild Stress(Y.S)N/mm2 | Tensile Stress(T.S)N/mm2 |
|---|---|---|
S30400 / 304 | 205 | 515 |
S30403 / 304L | 170 | 485 |
S301603 / 316L | 170 | 485 |
Tolerance of Thickness for Cold rolled Coil
Width (W, mm)
TE
ASTM A480
EN 10051
W ≦1250
W≦1500
W≦1200
1200<W≦1500
Nominal
Thickness
(T, mm)
T≦2.00 | ±0.13 | ±0.18 | ±0.13 | ±0.14 |
|---|---|---|---|---|
2.00<T≦2.50 | ±0.14 | ±0.20 | ±0.14 | ±0.16 |
2.50<T≦3.00 | ±0.15 | ±0.25 | ±0.15 | ±0.17 |
3.00<T≦3.50 | ±0.17 | ±0.30 | ±0.17 | ±0.18 |
3.50<T≦4.00 | ±0.17 | -0.25/+0.47 | ±0.17 | ±0.18 |
4.00<T≦5.00 | ±0.18 | -0.25/+0.47 | ±0.18 | ±0.20 |
5.00<T≦6.00 | ±0.20 | -0.25/+0.51 | ±0.20 | ±0.21 |
6.00<T≦8.00 | ±0.22 | -0.25/+0.51 | ±0.22 | ±0.23 |
1. The thickness is measured at any point located more than 20mm from the edges in the case of slit edges and at any point located more than 30mm from the edges in the case of mill edges, if the tolerances according to EN ISO 9445 are chosen.
2. The thickness is measured at any point located more than 15mm from the edges in the case of slit edges and at any point located more than 25mm from the edges in the case of mill edges, if the tolerances according to ASTM A480 or EN ISO 9445 are chosen.
bottom of page